PlateScope™ User Guide
PLATESCOPE 8 User Interface Main Screen Overview When the instrument is powered-up, the main (top level) screen appears after the diagnostics test is
PLATESCOPE 9 Instrument Controls The instrument controls are used to navigate the screen, configure options, and perform measurements. Top View Nav
PLATESCOPE 10 Taking a Measurement Below is an example of how to perform a typical measurement. Each mode will be explained in greater detail on the f
PLATESCOPE 11 Configuration Mode Configuration mode is used to adjust and view the instrument’s settings. Certain icons display the current settings.
PLATESCOPE 12 Idle Screen Setting This screen is used to set the amount of nonuse time that elapses before the display returns to the splash screen. T
PLATESCOPE 13 Time and Date Format The Time and Date Format screen allows you to adjust the date format and view the instrument’s current time and dat
PLATESCOPE 14 Language Setting This screen is used to set the language that is displayed on the instrument. To select the language: 1. From the Confi
PLATESCOPE 15 Units Setting This screen is used to set the displayed units. The setting can be set to inches (in) or centimeters (cm). To adjust the u
PLATESCOPE 16 Plate Setting This screen is used to select the plate type that the instrument will be measuring. To select the plate: 1. From the Conf
PLATESCOPE 17 Information Mode This screen contains technical information about the instrument, and an option to restore the configuration settings to
PLATESCOPE 18 Calibration Mode You only need to calibrate the instrument if the measurement performance is in question, if it has been dropped or if i
PLATESCOPE 19 5. Press a Measure button to take the measurement. The screen displays a “checkmark” over the patch icon if the patch was successfully
PLATESCOPE 20 10. Press the Measure button or use the Next Arrow icon to active targeting mode. 11. Locate the instrument’s target window on the 10% p
PLATESCOPE 21 Spot Measurement Mode The spot measurement mode is used to take measurements on an offset plate and display the results. A graphical rep
PLATESCOPE 22 Substrate Type (Plate or Paper ) Used to select offset plate or printed paper substrate. Illumination Option (Red, Green, Blue, White
PLATESCOPE 23 Zoom Mode The image area of the last sample measured can be zoomed for easier viewing. The instrument supports two times (x2) and four t
PLATESCOPE 24 Strip Measurement Mode The strip measurement mode is used for measuring a defined “seven patch” strip in sequential order. Data is displ
PLATESCOPE 25 NOTE: The settings cannot be changed once the measurement sequence has started. All patches must be deleted before settings can once aga
PLATESCOPE 26 If a mistake was made and you would like to re-measure the patch, use the Navigation Ring to move the highlight focus to Delete icon and
PLATESCOPE 27 Deleting the Stored Strip Data Stored strip data is deleted from the main strip screen. All stored strips are deleted at one time; indiv
PLATESCOPE 1 CE Declaration Manufacturer's Name: X-Rite, Incorporated Authorized Representative: X-Rite, Incorporated Siemensstraße 12b • 6326
PLATESCOPE 28 Appendices Service Information The instrument is covered by a one-year limited warranty and should be referred to an authorized service
PLATESCOPE 29 Cleaning the Instrument Your instrument requires very little maintenance to achieve years of reliable operation. However, to protect you
PLATESCOPE 30 Replacing the Battery Pack Use only X-Rite battery pack (NiMH) P/N SE15-38; other types may burst causing personal injury. 1. Unplug th
PLATESCOPE 31 Troubleshooting Prior to contacting X-Rite support department for instrument problems, try the applicable solution(s) described below. I
PLATESCOPE 32 Screen Messages Screen messages can appear on the display during error conditions or for informational purposes. All messages are accomp
PLATESCOPE 33 Instrument Specifications General Targeting/Measurement Array Patent-pending split-beam integrated color targeting and precision optica
Corporate Headquarters - USA 4300 44th Street SE Grand Rapids, Michigan 49512 Phone 1 800 248 9748 or 1 616 803 2100 Fax 1 800 292 4437 or 1 616 8
PLATESCOPE 2 Proprietary Notice The information contained in this manual is derived from patent and proprietary data of X-Rite, Incorporated. The cont
PLATESCOPE 3 Table of Contents Introduction and Setup 4 How to Use this Manual 4 Packaging 4 Applying Power 5 Power Modes 5 Instrument’s Internal
PLATESCOPE 4 Introduction and Setup The PlateScope instrument accurately measures even the most difficult low-contrast, chemistry-free and processless
PLATESCOPE 5 Applying Power The Select button is used to initiate the instrument from a power down state. Simply press the button to turn on the inst
PLATESCOPE 6 Charging the Batteries Your new PlateScope comes in a discharged condition and must be charged before use (up to 4 hours for full charge)
PLATESCOPE 7 Connecting the USB Cable IMPORTANT: You must install the PQS software before connecting the instrument to your computer. NOTE: FOR WINDO
Comments to this Manuals